oil water separator transformer oil purifier three stage transformer oil purifier unit
The vacuum oil filter is designed based on the principle of different boiling points of water and oil. It consists of a vacuum heating tank, a fine filter, a condenser, a primary filter, a water tank, a vacuum pump, a drainage pump, and an electrical cabinet. The vacuum pump extracts the air from the vacuum tank to form a vacuum. Under the action of atmospheric pressure, the external oil enters the primary filter through an inlet pipeline to remove larger particles, and then enters the heating tank. After heating, the oil at 40-75 ºC passes through an automatic oil float valve, which automatically controls the balance of oil entering and exiting the vacuum tank.
After heating, the oil is separated into a semi mist by the rapid rotation of the spray wings. The water in the oil rapidly evaporates into water vapor and is continuously sucked into the condenser by a vacuum pump. The water vapor entering the condenser is cooled and then returned to the original water for discharge. The oil in the vacuum heating tank is discharged into the fine filter by the oil discharge pump and filtered out by the oil filter paper or filter element to quickly remove impurities, water, and gas from the oil. This completes the entire process of the vacuum oil filter, allowing clean oil to be discharged from the oil outlet.
equipment performance:
1. Vacuum system: composed of vacuum tank, vacuum pump, condenser tank, liquid accumulation tank, and air replenishment system. By adopting optimized structural design, the surface area of the oil in the vacuum system has been greatly increased, and the travel of the oil in the vacuum system has been maximized, allowing water and gas in the oil to fully overflow. This machine adopts an advanced defoaming system, which ensures that the oil filter will never experience the common fuel injection phenomenon of similar products during operation.
2. Filtering system: adopts three-stage filtration, with a coarse filter at the oil suction port to protect the oil pump and extend the service life of the main filter. There are two stages of fine filters behind the pump, allowing the oil to quickly reach a high level of cleanliness. The filter material adopts special gradient aperture glass fiber material, which can layer and filter particles of different sizes, greatly improving the service life of the filter element. With a perfect filter structure, it can effectively reduce the surface flow rate of the filter material and achieve stable filtration accuracy.
3. Heating system: adopts segmented and step-by-step heating, with a surface heat load less than l OW/cm2, will not overheat and cause oil deterioration. The oil temperature can be adjusted freely between 0~100 ° C, automatically controlled, and equipped with a protective device. When the oil intake is too low, it automatically stops working to avoid damage to the heater caused by dry burning.
4. Automatic control system: This machine adopts a series of automatic control instruments such as frequency converter, liquid level transmitter, temperature sensor, vacuum degree sensor, etc. to collect various information about the operation of the equipment, which is processed by the central processor. It automatically controls the operation of the entire equipment and monitors its operation status. This machine is equipped with various protection devices (overload protection, overvoltage protection, phase sequence protection, abnormal operation shutdown protection), It can ensure the safe operation of the equipment.
5.Whole machine structure: The integrated bridge structure of the whole machine reduces its volume. It adopts an integral detachable oil tank to ensure oil-free operation on the ground and reduce environmental pollution. There are various models to choose from, including mobile, fixed, fully enclosed, and vehicle mounted
Equipment site diagram:
Application scope:
Filter new oil; Add new oil and filter it; Purify the oil in use; The bypass filtration during the operation of the hydraulic lubrication system.
FAQ:
Q1.What is your packing clause?
Answer:generally, we put our goods in neutral white boxes and brown cartons. Or customize any kind of packing according to your request. If you have registered a patent legally,We can put the goods in your brand packing box after receiving your authorization.
Q2.What is your payment condition?
Answer: T / T 30% as a margin, 70% before delivery.Before the balance is paid, we will show you the photos of the products and packaging.
Q3.What is your delivery condition?
Answer: EXW, FOB, CFR, CIF, DDU.
Q4.What's your delivery time?
A:Generally speaking,it takes 30 to 60 days after receiving the advance payment.The exact time of delivery depends on the items and quantities of your order.
Q5. Can you make it according to the sample?
Answer:Yes,we can produce it through your sample or technical drawings.We can build molds and fixtures.
Q6.What is your sample policy?
Answer:if we have spare parts in stock, we can provide the sample, but the customer must pay the sample cost and the cost of the sample.Express delivery cost.
Q7.Did you test all the goods before delivery?
Answer: Yes, we have 100% tests before delivery.
Q8: how do you make our business a long and good relationship?
Answer: 1. We maintain good quality and competitive price to ensure our customers benefit.
Audited Supplier 
){kind=link}